Skip to content
Manufacturing and factories

Shift-based payroll for factory floors, with overtime and compliance in one place

Small and mid-sized factories run shifts, overtime and mixed pay grades. Saralix ties the shift roster to attendance and payroll so the month closes without a sheet-by-sheet reconciliation.

Typical size: 30 to 100 employees

Who this is for

Small and mid-sized manufacturing units, workshops and processing plants with roughly 20 to 100 people on their own payroll. Workers run in shifts, supervisors and office staff are on monthly salary, and overtime is common during peak orders.

Where it hurts

What factory payroll usually struggles with

Shift changes and night shifts

Workers swap shifts, weekly offs rotate and a night shift ends after midnight. Late and early marks go wrong when the roster lives on a whiteboard.

Overtime disputes

Hours are noted on paper, approved verbally and argued about at month end. Nobody can say what was agreed.

Minimum wage and grade rules

Wages must stay above the state minimum for each skill category, and a revision can leave someone below it without anyone noticing.

ESI and PF coverage

A mix of lower-paid workers and higher-paid staff means ESI applies to some people and not others, and PF wages differ by employee.

Punches from a device that does not talk to payroll

Biometric machines collect punches, then someone exports and re-types them into a sheet.

Need to feature

What you need, and where Saralix handles it

Your needWhat handles it in Saralix
Plan shifts and weekly offs by dayShift roster with weekly grid, copy last week, and night shifts that close after midnight
Bring biometric punches into attendanceBiometric devices push punches to a keyed API, or upload a spreadsheet or biometric software export with a dry run
Pay overtime at the right rateOvertime listed in payroll review, edited to approved hours, paid at 2x the hourly rate, with a flag above 50 hours
Stay above minimum wageMinimum wage master by state and skill category, flags in payroll and a shortfall report
Different pay structures for workers and staffNamed salary templates for grades, with bulk moves between templates
Compensate for working a weekly offComp off claims checked against shift, holidays and attendance
Give advances to workersLoans and advances recovered monthly through payroll
File PF, ESI, PT and LWFLiabilities from each locked payroll, ECR file, ESI columns and challan tracking
Checked in
09:42
Inside office geofence
M
T
W
T
F
Optional selfie and GPS, flowing into leave and loss of pay.
A typical month

How the month runs

  1. 01

    Before the month starts

    Supervisors plan the shift roster for the coming weeks and copy last week where nothing changes. Weekly offs are set for each group.

  2. 02

    Through the month

    Workers punch on the biometric device or on a phone. Punches reach attendance. Overtime hours are recorded in attendance.

  3. 03

    Cut-off

    Supervisors clear attendance corrections. HR checks the minimum wage report for anyone under the limit for their skill category.

  4. 04

    Payroll days

    Overtime is edited to the approved hours in the payroll review, salary advance instalments are deducted, and a second person approves and locks.

  5. 05

    After payroll

    Payslips are published, the bank file is exported and PF, ESI and PT liabilities are paid and recorded against their due dates.

Statutory notes

As we understand it, PF is 12% a side on basic plus dearness allowance up to the wage ceiling (Rs 15,000 until 16 September 2026, Rs 25,000 for mandatory coverage after that, with EPFO's circular awaited), and ESI applies to employees earning up to Rs 21,000 a month, with 0.75% from the employee and 3.25% from the employer. Overtime is typically paid at double the ordinary rate under factory law, but state rules and the Labour Codes transition may change details. Minimum wages vary by state, zone and skill. Check the current notification for your state. Verify against current rules.

What is not covered yet

Saralix does not run payroll for contract labour supplied by a contractor, and it does not file returns with the Factories Inspectorate or manage licences. The biometric link is an API that devices push punches to. We make no claims about specific device brands. Overtime follows the 2x ordinary rate rule with hours you edit, and piece-rate pay is not a built-in mode. Professional Tax tables cover seven states and Labour Welfare Fund covers Gujarat and Maharashtra, so factories elsewhere will see a payslip warning.

Fit with pricing

A factory with 11 to 100 employees is on the Business plan at Rs 99 per employee per month plus GST, applied to every employee once you are above 10. A workshop with up to 10 employees and one admin can use the free plan. Larger units above 100 employees are on Enterprise with a contract rate.

See pricing

Questions

Can the roster handle night shifts?

Yes. A check-out after midnight closes the shift that began the previous day, so night shifts are counted against the right date.

How does overtime get into payroll?

Overtime recorded in attendance is listed per employee in the payroll review. You edit hours to what was approved, and it is paid at 2x the ordinary hourly rate, calculated from monthly gross over 26 days and 8 hours by default.

Do you work with our biometric machines?

Devices can push punches to a keyed API, and you can also upload a spreadsheet or software export. We do not claim support for particular hardware brands, so check with your vendor that the device can call the API.

Does it check minimum wage?

Yes. The statutory master holds minimum wages by state and optional skill category, payroll flags anyone below it, and a report lists the shortfall.

Can we pay contract labour through it?

No. Saralix does not run contractor payroll. It covers employees on your own payroll.

Related reading and tools

Other industries

See it with your own numbers.

Free for up to 10 employees. Business is Rs 99 per employee per month up to 100. Above 100, we quote.